Brick Paver Installation & Edging



Staging of material

The majority of paver tasks will vary depending on access, site conditions, project size and of course, the weather. Mindful factor to consider ought to be taken to identify the time to begin the paver installation.

The supervisor or project manager need to constantly have the materials (sand/ pavers) distributed around the task website for simple and efficient setups. Paver pallets/bundles ought to be positioned in a manner not to interfere with the paver installation. The appropriate pallet/bundle placement can make the real task installation easier and quicker by decreasing the general labor of managing the product.

Brick paver patterns

Pavers can be positioned in many different patterns depending on their shape. Each paver shape will normally have a number of different hatch patterns that are offered by the producer.

Professionals need to take into consideration the traffic weight loads on their paver jobs. In many applications worldwide, it has been shown that pavers laid in a herringbone pattern have performed adequately.

Pavers that are 60 mm (2 - 3/8 in) density appropriate for pedestrian applications. Pavers that are going to be used in industrial or commercial applications should be 80 mm (3 - 1/8 in) in density.

Reference/starting point for brick paver installation

There are a variety of conditions that figure out the beginning point of a paver job.

When starting to install pavers it is best to snap a true straight chalk line on the surface of the bed linen sand or pull a real straight string line above the surface area of the bedding sand at the completed elevation of the pavers This will help as a guide for maintaining straight joint lines and will also allow the installer to make adjustments in the alignment of the pavers.

Structures and concrete suppressing are normally not straight and must not be used for establishing straight joint lines. The use of string lines is vital to figure out the true straightness of the edge also. As the paver installation advances, the string lines will help minimize the requirement for small trim pieces.

Joint width between pavers ought to be between 1/16 and 3/16 in (2 and 5 mm ). There are some pavers with spacer bars on their sides. These will keep a minimum joint width and enable the bedding and jointing sand to enter in between each paver. Pavers with spacer bars are normally not laid in snug against each other since a string line will supply consistent joint spacing.

Installation of brick pavers.

One of the most commonly utilized approaches for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have actually pulled or above the bed linen sand. The finest method is to put a paver against another one and let it move down into the bed linen sand.

When installing pavers on a steep grade, they must be set up at the base of the grade going uphill. This will avoid the pavers from creeping as they are being laid.

The finest method for setting up pavers on big projects is to install them mechanically. There are a couple items a professional must think about prior to setting up pavers mechanically:

1.) Mechanical installers are just efficient in installing pavers in certain patterns.

2.) The contractor should ensure that the producer can production and bundling pavers in the wanted pattern on the pallets for simple mechanical installation.

Poor color blending could result in an irregular looking installation. The majority of makers are consistent with color blending on each bundle of pavers, however it is the specialist's duty to make sure correct mixing in the field.

Cutting treatments for brick pavers.

Professionals usually have 2 ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will offer a much cleaner and more accurate cut. Most brick saws will have a hose attachment on them which will permit the operator to cut the pavers damp. When cutting pavers damp, it will help reduce dust and will prolong the diamond blades life. The operator of the brick saw should constantly cut the pavers far from the surface area of the paver field when cutting wet, due to the fact that the pavers will create a slurry that will stain the paver surface area. Pavers that are cut need to not fit tight, enough spacing must be offered for jointing sand.

The brick saw operator must constantly wear the proper defense that is required for operating a saw, such as eye, ear, respiratory and hand defense ).

Edging types

Edge restraints play a significant role in the overall success of an interlocking pavement Patio Pavers West Palm Beach installation Edging restraints remove lateral movement of the pavers and hold the pavers securely together. Particularly at the outer border of the paver application, without an edging restraint, your task is ensured to stop working gradually.

There are several different edging restraints from which specialists can choose. Usually produced edge restraints are the most commonly utilized by professionals. Made edging restraints can vary from, plastic edging, steel and aluminum, timbers or precast concrete and stone. An edging type that is utilized mainly in industrial and business applications is poured-in-place concrete curbs. This edging restraint is usually installed by other specialists.

Edging installation.

When installing your edge restraint, it ought to rest straight on top of the compacted gravel base. The compacted gravel base course must extend a minimum of 6in beyond the perimeter of the pavers This will supply a proper structure upon which the edging restraint can sit. Produced edging (i.E. Plastic, steel or aluminum) need to be securely anchored into the compressed gravel base( talk to the manufacturer's literature for the suggested spacing of the spikes). There are some edging restraints that will extend deeper into the gravel base or beyond the base course (i.E. Timbers or poured-in-place curbs ). Edging restraints must never be put straight on top of the bedding sand. This might result in the migration of the bed linen sand and eventual lateral motion of the pavers. Geo textile material is recommended if there is a possibility of losing bed linen sand in between the pavers and the edge restraint. When a gap in between the pavers and the edging exceeds 3/8" (10mm), then the area needs to be filled with cut pavers. All edging applications ought to be effectively back filled after they are installed to assist provide additional stability.

Compaction of brick pavers.

After installation, the pavers have to be compressed. The entire location that is to be compressed ought to be swept tidy of any foreign things and debris that can cause scuffing or scratching on the surface of the pavers.

In addition, it is crucial that the very first compaction takes location prior to any jointing sand has actually been used to the pavers. If jointing sand is used to the pavers prior to compaction takes location, this can trigger a bridging issue and will not enable the joints to be totally filled with jointing sand. This can also prevent the pavers from being correctly set into the bedding sand.

When compacting the pavers, it is recommended that you make at least two passes in different instructions throughout the pavers. This will enable the pavers to be appropriately embeded in the bedding sand and will force the bedding sand up into the joints from the bottom of the pavers.

The compaction of the pavers is very critical to the final efficiency of the pavers. Failure to do correct compaction can lead to contortions and pavement failure in time.


Paver pallets/bundles ought to be placed in a manner not to interfere with the paver installation. One of the most widely utilized approaches for the installation of pavers is hand installation of each paver. The operator of the brick saw need to constantly cut the pavers away from the surface area of the paver field when cutting wet, due to the fact that the pavers will create a slurry that will stain the paver surface area. Edging restraints remove lateral motion of the pavers and hold the pavers firmly together. When a gap between the pavers and the edging goes beyond 3/8" (10mm), then the area should be filled with cut pavers.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Brick Paver Installation & Edging”

Leave a Reply

Gravatar